Delray Beach, FL

Work Performed: Installed Halo whole-home water filtration system Set and secured Halo media tank in designated location Connected system to main water supply line with all necessary piping and fittings Installed and configured Halo control valve for proper operation Integrated filtration system with existing plumbing and ensured correct flow direction Installed drain line connection for system discharge Tested system for proper function and checked for leaks at all connection points Verified water pressure and system performance Cleaned up work area upon completion.

Kitchen Plumbing Repair: Homeowner reported a foul odor and slow drainage coming from the kitchen sink. Inspected the drain system and found buildup within the branch line along with minor venting issues. Cleared the line using professional equipment, flushed the system, and verified proper vent function. Sink now drains efficiently with no lingering odors.

Work Performed: Supplied and professionally installed whole house water filtration and softening system Installed (2) main treatment tanks including control valve and media tanks Installed pre-filtration housing with replaceable filter cartridge Installed brine tank for water softener system Connected system to main water supply with all necessary piping and fittings Installed inlet and outlet shutoff valves for serviceability Secured all plumbing connections and ensured proper system configuration Programmed control head for proper regeneration cycle Tested system for proper operation and ensured no leaks present Verified water flow and system functionality throughout home Cleaned up work area upon completion

Work Performed: Supplied and professionally installed (1) new InSinkErator 1/2 HP Garbage Disposal Removed existing faulty disposal unit and prepared sink opening for new installation Installed new mounting assembly and secured disposal to sink flange Connected disposal to existing drain line and dishwasher discharge line Reconfigured tubular piping as needed to ensure proper alignment and drainage Connected electrical supply and verified proper power operation (120V system typical) Tested unit for proper grinding operation and confirmed no leaks present Cleaned up work area upon completion

Work Performed: Opened sheetrock wall to access active water leak within wall cavity Located damaged section of copper piping causing spray leak Removed compromised pipe section and fittings Supplied and installed new copper pipe section with proper fittings and secure connections Restored water service and tested repair under pressure Verified no further leaks present and ensured proper system operation Advised customer on drywall repair for wall restoration Cleaned up work area upon completion and removed all debris

Work Performed: Opened wall to expose existing plumbing system and drain assembly Evaluated existing drain configuration and identified required modifications Removed and reconfigured existing drain piping to accommodate new layout Installed new shower drain assembly and properly secured to waste line Set drain at correct elevation and ensured proper alignment with shower base Verified proper pitch on drain line to promote optimal drainage flow Supported and secured all piping within wall cavity to meet code standards Performed test to confirm proper drainage and verified no leaks at connections Prepared area for concrete patch and coordinated placement around new drain Oversaw and ensured proper concrete patching and finish around drain opening Cleaned and organized work area, leaving installation ready for next phase of construction

Work Performed: Removed existing toilet and disposed of unit in accordance with local regulations Inspected closet flange and surrounding area for integrity and proper alignment Prepared installation area and ensured clean, level surface for new fixture Supplied and installed new wax seal and closet bolts for secure connection Set and secured new toilet in place, ensuring proper alignment and stability Connected water supply line and verified proper fill valve operation Tested toilet for proper flushing performance and drainage functionality Inspected all connections and confirmed no leaks present at base or supply line Applied final adjustments to ensure optimal operation and secure fit Cleaned work area and removed all installation debris upon completion

Underground copper water line repair completed along the exterior wall. Damaged section was removed and replaced with new copper and secure fittings. Line was pressure tested to confirm no leaks and proper water flow before backfilling.

Work Performed: • Located main sewer cleanout access point • Set up electric drain cleaning equipment • Performed electric cleaning of main sewer line from cleanout to remove buildup and obstructions • Restored proper flow and drainage • Tested system to confirm line was clear and functioning properly • Cleaned up work area upon completion

Work Performed: • Supplied and installed new double-basin stainless steel kitchen sink • Installed new kitchen faucet and secured to sink deck • Reconnected hot and cold water supply lines to faucet • Reconnected drain assemblies to both sink basins • Installed and secured sink strainer assemblies • Checked all connections for proper operation and verified no leaks present • Cleaned up work area upon completion

Work Performed: • Supplied and installed one new toilet fill valve • Supplied and installed one new toilet flapper • Supplied and installed one new commode toilet supply line • Tested toilet for proper operation and verified correct water level and flush performance • Checked for leaks at all connections • Cleaned up work area upon completion

Work Performed: • Performed professional drain cleaning to remove blockage and restore proper flow • Utilized appropriate equipment to clear buildup and obstructions within the line • Verified proper drainage and system operation after service • Tested for proper operation and ensured no leaks present • Cleaned up work area upon completion

Work Performed: • Removed existing worn 2-inch flapper from bathroom commode. • Supplied and installed new 2-inch flapper. • Adjusted chain and tested flush operation for proper seal and performance. • Removed damaged overflow assembly on second bathroom commode. • Supplied and installed new overflow assembly. • Verified proper fill and drain operation with no leaks present. • Cleaned up work area upon completion.

Work Performed: • Supplied and installed one AO Smith 50-gallon hot water heater • Installed new thermal expansion tank as required • Connected unit to existing water and electrical systems • Tested system for proper operation and verified correct temperature settings • 6-year manufacturer warranty on the water heater • 1-year workmanship warranty provided by Florida Flush Plumbing • Removed and disposed of old water heater • Cleaned up work area upon completion

Work Performed: Removed existing shower valve and damaged downspout pipe Supplied and installed new shower valve assembly Replaced downspout pipe section and made all necessary connections Installed new access panel for future serviceability Secured and sealed all fittings to ensure proper operation and no leaks Tested system for correct function and water flow Cleaned up work area upon completion

Scope of Work: Install customer supplied commodes tank and bowl (2) Remove and dispose of existing commodes tanks and bowls Install new tanks and bowls with new wax rings bolts and water supply lines Install 2 new toilet shut off valves Test for proper operation and ensure no leaks present

Work Performed: • Supplied and installed one new water heater • Supplied and installed one new thermal expansion tank • Connected water heater to existing water piping and electrical connections • Secured expansion tank to cold water supply line • Tested system for proper operation and ensured no leaks present • Cleaned up work area upon completion

Work Performed: • Removed existing kitchen faucet and associated supply connections • Supplied and installed new commercial-style pull-down kitchen faucet • Connected hot and cold water supply lines and secured all mounting hardware • Tested faucet for proper operation including spray function and water flow • Checked for leaks and verified correct functionality • Cleaned up work area upon completion

Garbage Disposal Repair: The homeowner heard grinding and rattling from their disposal. After inspecting the unit, I found a loose impeller plate and metallic debris inside the chamber. I removed the debris, tightened the components, and ensured the disposal ran smoothly and safely.

Well Pump Repair: Arrived at the client’s property after reports of low water pressure and intermittent water supply. Inspected the well system and determined the submersible pump was failing due to a worn impeller and partial motor obstruction. Safely disconnected power, pulled the pump from the well, and cleaned the components before installing replacement parts. Reassembled and lowered the pump back into place, restored power, and tested the system to confirm proper pressure and consistent water flow. The well pump is now operating reliably and at full performance.

Water Heater Repair: Arrived at the client’s home after reports of inconsistent water temperature from the water heater. Inspected the unit and found a faulty thermostat and sediment buildup affecting heating performance. Spoke with the client, drained and flushed the tank to remove sediment, replaced the defective thermostat, and tested the unit for consistent temperature regulation. Verified proper operation and informed the client that the water heater is now heating reliably and efficiently.

Investigated water damage in a wall and traced it to a hidden leak in the supply line. Used electronic leak detection equipment to locate the source, then repaired the copper line. The repair stopped the leak, preventing further damage to the home.

Installed a new tank-style water heater to replace an older unit that was leaking from the base. Connected all water and gas lines, tested the system, and ensured proper venting. The new water heater is heating efficiently and safely.

A customer’s disposal was humming but not spinning. This can sometimes be a jammed flywheel, but in this case, the motor had seized. We recommended replacement due to age and damage. Installed a ½ HP continuous-feed disposal and tested for leaks. Kitchen is back in business!