West Palm Beach, FL

Plumbing Installation: Installed a prep sink in a newly renovated kitchen island for added convenience during cooking and cleanup. Ran new hot and cold water supply lines beneath the floor, connected the drain line to the main branch, and installed the sink with a garbage disposal unit. Tested water flow, drainage, and disposal operation. New fixture is fully functional and ready for daily use.

Work Performed: • Completed kitchen sink area remodeling and finish installation. • Removed existing sink area components as needed to prepare for new installation. • Prepared sink base cabinet for installation of new apron front farmhouse style sink. • Made necessary cabinet adjustments to properly fit and support new sink. • Installed proper support framing inside cabinet base to carry weight of farmhouse sink. • Set and secured new white farmhouse sink in place. • Checked sink alignment with countertop cabinet face and surrounding finished surfaces. • Completed countertop preparation and finish work around sink opening. • Installed new bridge style kitchen faucet with matching finish. • Installed matching side sprayer and accessory trim. • Installed new drain assembly and connected sink drain piping below cabinet. • Installed new water supply connections for hot and cold lines. • Connected faucet supply lines and verified proper water flow. • Secured plumbing connect

Work Performed: • Removed existing bathroom vanity and prepared plumbing connections for new fixture installation • Supplied and installed new bathroom vanity cabinet with integrated countertop and sink assembly • Installed new bathroom faucet with all necessary water supply lines and plumbing connections • Installed new sink drain assembly and connected to existing drainage system • Secured vanity and plumbing fixtures properly ensuring level alignment and professional installation • Performed adjustments to faucet operation and drain flow for proper functionality • Tested lavatory sink faucet and drain system for leak free performance and proper operation • Verified all plumbing connections were sealed correctly and cleaned work area upon completion.

Work Performed: • Supplied and installed one new AO Smith electric tank style water heater. • Removed existing water heater as needed and prepared the installation area for the new unit. • Set new water heater in place on existing water heater pan and positioned unit properly for connection to the plumbing and electrical system. • Installed and connected new thermal expansion tank to help protect the plumbing system from pressure changes caused by heated water expansion. • Reconnected cold water supply line to the new water heater. • Reconnected hot water outlet line from the new water heater to the existing plumbing system. • Installed and connected necessary fittings, adapters, supply connections, and piping materials required for proper installation. • Connected water heater to existing electrical supply and secured electrical connection at the top of the unit. • Verified proper connection of the hot and cold water lines. • Filled the new water heater c

Work Performed: • Supplied and installed two new commercial grade tank style water heaters. • Removed existing water heater units and prepared the installation area for the new equipment. • Set both new water heaters securely in place and positioned them properly for connection to the existing plumbing and gas system. • Reconnected hot and cold water piping to both water heater units using the required copper piping, fittings, and adapters. • Installed and connected new copper water lines to properly tie both water heaters into the building’s plumbing system. • Installed new shutoff valves where needed to allow each water heater to be properly isolated for future service and maintenance. • Connected gas supply lines to both water heaters and ensured proper connection to each gas control valve. • Reconnected venting for both water heaters and verified that the vent piping was properly aligned and secured. • Installed and connected thermal expansion tank to hel

Work Performed: • Installed new tankless water heater system in mechanical room area. • Mounted tankless water heater securely to wall and connected unit to existing plumbing system. • Installed and connected new copper hot and cold water piping for proper water distribution. • Ran new copper piping along wall in a clean and organized layout to support the tankless water heater installation. • Installed new shutoff valves and necessary fittings to allow proper service access to the water heater and connected plumbing lines. • Connected hot and cold water supply lines to the tankless water heater using proper fittings and secure connections. • Installed new water treatment equipment and connected unit into the main water supply system. • Completed copper piping connections between the water treatment system and the tankless water heater setup. • Secured piping to maintain a neat professional appearance and to reduce unnecessary movement or stress on the plumbi

Work Performed: • Supplied and installed under-sink reverse osmosis filtration system • Mounted filtration assembly inside kitchen sink cabinet • Installed RO storage tank and connected system tubing • Connected filtration system to existing cold water supply • Installed and secured all filter cartridges and housings • Connected filtered water line to dedicated faucet/dispenser • Tied system drain line into existing sink drain assembly • Pressurized system and checked all tubing connections • Tested filtration system for proper operation and water flow • Checked all water and drain connections for leaks • Cleaned up work area upon completion.

Work Performed: • Opened wall area to access existing plumbing rough-in • Reworked and installed PVC drain and vent piping inside wall cavity • Installed new fittings to properly tie drain line into existing plumbing system • Ran and secured hot and cold water lines as needed • Checked all new plumbing connections for proper fit and alignment • Tested for proper drainage and ensured no leaks present • Cleaned up work area upon completion.

Work Performed: • Repaired and reconfigured copper water heater piping near expansion tank connection • Supplied and installed new copper fittings and piping as needed • Secured threaded connections for proper seal • Restored proper water line connection between water heater and expansion tank • Tested for proper operation and ensured no leaks present • Cleaned up work area upon completion.

Work Performed: Supplied and installed new bathroom sink drain waste assembly. Installed new tubular P-trap assembly under bathroom sink. Connected sink drain piping from sink tailpiece to existing wall drain connection. Adjusted and secured drain piping for proper alignment and fit. Inspected existing hot and cold water supply connections under sink. Tested sink faucet and drain for proper operation. Ran water through drain system to confirm proper flow. Checked all visible drain connections and supply connections to ensure no leaks present. Cleaned up work area upon completion.

Work Performed: Supplied and installed new electric hot water heater in existing water heater location. Removed existing water heater and prepared area for new installation. Installed new water heater pan underneath unit for added protection. Reconnected hot and cold water piping to new water heater. Supplied and installed new shutoff valve for proper water control at the unit. Connected existing electrical wiring to new electric water heater. Reconnected existing condensate/drain piping as needed. Filled water heater and properly purged air from the system before startup. Tested hot water heater for proper operation and heating function. Checked all visible water connections and fittings to ensure no leaks present. Includes 6 year manufacturer warranty on water heater. Cleaned up work area upon completion.

Work Performed: Arrived on site and located damaged underground water/service line in exterior excavation area. Exposed affected piping section and removed surrounding debris for safe repair access. Shut down water supply prior to repair work. Pumped standing water from excavation area as needed to complete service. Removed broken section of underground PVC piping and damaged fittings. Supplied and installed new Schedule 40 PVC piping with new elbows couplings and fittings as required. Completed solvent welded connections and reconfigured piping for proper alignment. Allowed joints to cure and restored water service. Pressure tested repaired line under operating conditions. Verified proper water flow through system after repair completion. Inspected repaired connections and confirmed no leaks present. Backfill and final ground restoration to be completed as conditions allow or by others unless requested. Cleaned work area

Work Performed: Arrived on site and located leaking water line within wall cavity. Opened access area to expose damaged copper piping and fittings. Shut down water supply and drained existing line prior to repair. Removed compromised section of copper pipe and defective fittings. Supplied and installed new type L copper piping with new tees couplings and fittings as required. Completed professional soldered connections and secured piping assembly. Reconfigured piping section for improved alignment and support. Restored water service and pressurized system. Tested repaired water line under operating pressure. Inspected all newly installed joints and confirmed no leaks present. Verified proper water flow through branch line and main supply section. Advised customer wall area is ready for patching by others unless requested. Cleaned work area upon completion.

Work Performed: Arrived on site and inspected Roman tub faucet assembly due to reported operational issues. Shut down water supply to tub fixture and prepared work area for service. Removed existing worn faucet components and accessed valve bodies beneath deck mounted tub set. Supplied and installed new Roman tub faucet trim components including handles spout and diverter as needed. Replaced defective internal cartridges and seals to restore proper hot and cold water control. Secured all mounting hardware and ensured faucet assembly was properly aligned. Reconnected water supply and restored service to fixture. Tested hot and cold water operation for proper pressure and temperature control. Verified smooth handle movement and proper spout flow. Inspected surrounding tub deck area for leaks during operation. Confirmed drain and overflow area remained watertight during testing. Cleaned work area upon completion.

Work Performed: Removed existing laundry sink and faucet assembly Supplied and installed new utility/laundry sink Installed new faucet and secured to sink basin Connected hot and cold water supply lines with new fittings Installed and connected new drain assembly to existing plumbing Secured sink and ensured proper alignment and stability Restored water supply and tested for proper operation Checked for leaks at all supply and drain connections Verified proper drainage and flow Cleaned up work area upon completion.

Work Performed: Supplied and installed new shower fixture trim kit including valve trim, handle, and escutcheon Installed new shower head and handheld shower assembly Installed new tub spout (if applicable) and secured all components Connected fixtures to existing valve and plumbing system Ensured proper alignment and secure mounting of all trim pieces Restored water supply and tested for proper operation and water flow Checked for leaks at all connections and fittings Verified proper temperature control and pressure balance function Cleaned up work area upon completion.

Work Performed: Installed Halo whole-home water filtration system Set and secured Halo media tanks and brine tank in designated location Connected system to main water supply line with all necessary piping and fittings Installed and configured Halo control valves for proper operation Integrated filtration system with existing plumbing and ensured correct flow direction Installed drain line and overflow connections as required Tested system for proper function and checked for leaks at all connection points Verified water pressure and overall system performance Cleaned up work area upon completion.

Work Performed: • Removed existing brass flange from lead bend • Installed new PVC closet flange • Secured flange to floor with proper anchors and bolts • Ensured proper alignment and seal for toilet connection • Tested for proper operation and ensured no leaks present • Cleaned up work area upon completion.

Work Performed: • Disconnected and removed existing water heater unit from location • Inspected area and verified proper space, drainage, and electrical requirements for hybrid heat pump installation • Installed customer-supplied Rheem ProTerra Performance Hybrid Heat Pump Water Heater • Supplied and installed all necessary materials including water supply lines, shut-off valve, fittings, and connections • Installed appropriate discharge piping for temperature and pressure relief valve • Drilled penetration through exterior wall and piped discharge line to terminate safely outside • Connected unit to existing electrical supply and verified proper voltage • Ensured proper condensate drain setup for hybrid system operation • Secured unit in place and ensured compliance with manufacturer specifications and local plumbing code • Filled system and tested for proper operation and heating performance • Checked all connections and verified no leaks present • Cleaned up work area up

Plumbing Repair Service: Dispatched for low water pressure throughout the home. Inspected main supply line and found mineral buildup restricting flow. Cleaned affected sections, replaced a partially blocked valve, and tested pressure at multiple fixtures. Water pressure is now fully restored across the property.

Work Performed: Removed existing drain components under kitchen sink Supplied and installed new PVC tubular drain assembly for double sink configuration Installed new P-trap and trap arm for proper drainage Connected drain line to existing garbage disposal outlet Reconfigured piping for proper alignment and slope Secured all slip joint connections and fittings Tested system for proper drainage and ensured no leaks present Cleaned up work area upon completion

Work Performed: Supplied and professionally installed (1) new A.O. Smith ProLine 50 gallon commercial grade electric water heater Installed new thermal expansion tank and properly secured above unit Connected hot and cold water supply lines with new fittings and dielectric connections Installed new electrical whip and completed proper electrical connections Set unit in place, leveled, and secured for safe operation Filled tank, purged air from system, and brought unit up to operating temperature Tested for proper operation and ensured no leaks present Cleaned up work area upon completion

Work Performed: Supplied and professionally installed (1) new Rheem Performance electric tankless water heater Mounted unit securely to wall and ensured proper alignment and support Installed new hot and cold water shutoff valves for serviceability Installed manufacturer approved isolation valve kit for maintenance and flushing Connected unit to existing water supply lines using stainless steel flex connectors Connected electrical conduit and ensured proper power supply to unit Secured all fittings and verified proper installation to code Tested system for proper operation, verified temperature performance, and confirmed no leaks present Cleaned up work area upon completion

Work Performed: • Supplied and professionally installed (1) new A.O. Smith 40-gallon electric hot water heater • Unit includes a 6-year manufacturer warranty for reliable long-term performance • Removed and properly disposed of existing water heater • Installed new thermal expansion tank to protect plumbing system from excess pressure • Supplied and installed new shutoff valve for improved control and safety • Connected all electrical and water supply lines in accordance with manufacturer specifications and local plumbing codes • Filled system, purged air from lines, and brought unit up to proper operating temperature • Tested system thoroughly for proper operation and confirmed no leaks present • Cleaned up work area and ensured job site was left in excellent condition

Work Performed: Removed existing toilet and exposed damaged/rotted closet flange Cleaned and prepped flange area, removing old wax and debris Removed deteriorated flange components and corroded hardware Supplied and installed new closet flange with proper secure anchoring Installed new closet bolts for toilet reset Ensured flange height and alignment were set correctly for proper seal Installed new wax ring and reset toilet Secured toilet and verified stability and proper positioning Turned on water supply and tested flush operation Checked for leaks at base and connections and ensured watertight seal Cleaned up work area upon completion and removed all debris