Boca Raton, FL

Plumbing Repair: Homeowner noticed water pooling behind the washing machine after every load. Inspection revealed a cracked drain standpipe and a loose hot water supply connection causing slow leakage during use. Replaced the damaged standpipe section, installed a new braided supply line, and tested the washer through a full cycle. Laundry area is now dry and operating without leaks.

Work Performed: • Installed new kitchen sink faucet • Installed new filtered water faucet/dispenser • Installed new soap dispenser • Secured all faucet trim and accessories for proper fit and alignment • Connected hot and cold water supply lines to kitchen faucet • Connected filtered water line to dedicated dispenser • Tested faucet sprayer and handle for proper operation • Tested filtered water dispenser for proper water flow • Checked all visible water connections under sink for leaks • Confirmed kitchen sink fixtures were operating properly upon completion • Cleaned up work area upon completion.

Work Performed: • Removed existing toilet seat as needed • Installed new bidet toilet seat attachment • Connected bidet water supply to existing toilet supply line • Secured bidet seat and adjusted for proper fit • Connected and checked water line connections • Tested bidet functions for proper operation • Tested toilet for proper flushing • Ensured no leaks present at toilet supply and bidet connections • Cleaned up work area upon completion.

Work Performed: Disassembled existing three handle tub and shower valve trim due to worn and leaking components. Removed deteriorated handles, escutcheon trim, and old internal stem assemblies as required. Supplied and installed new hot side stem, cold side stem, and center diverter stem assemblies. Installed new handle trim set with updated chrome finish. Replaced necessary washers, seats, and internal seals to restore proper shutoff. Reassembled complete faucet trim and aligned handles for proper operation. Tested hot, cold, and diverter functions for smooth performance. Verified tub spout flow and confirmed valves shut off correctly with no dripping present. Tested for proper operation and ensured no leaks present. Cleaned up work area upon completion.

Work Performed: Completed exterior water service piping repair at outside wall location. Opened and accessed affected exterior wall area as needed to expose existing water piping. Removed compromised or damaged section of existing exterior water line. Supplied and installed new copper piping, fittings, and transition connections as needed for proper repair. Supplied and installed new exterior hose bibb / hose faucet connection. Supplied and installed new shut off valve for improved water control at the exterior service line. Reconnected piping to existing water service connection and secured all new fittings properly. Restored water service and tested repaired piping for proper operation. Checked all visible copper connections, fittings, valves, and hose bibb connection to ensure no leaks present. Confirmed exterior hose bibb was operating properly at time of completion. Cleaned up work area upon completion.

Work Performed: Supplied and installed one new electric hot water heater in the existing location. Removed existing water heater and prepared the area for installation of the new unit. Set new water heater in place and ensured unit was properly positioned and secured. Reconnected hot and cold water service lines to the new water heater. Supplied and installed new thermal expansion tank mounted above the unit. Supplied and installed new shut off valve for proper water control to the water heater. Installed and connected all necessary dielectric fittings, piping, and materials required for a complete installation. Reconnected existing electrical supply to the new electric water heater. Filled water heater and properly purged air from the system before startup. Tested unit for proper heating operation and overall performance. Checked all visible water connections, fittings, and valves to ensure no leaks present. Includes 6 year manufacturer warranty on hot water heater. Clean

Work Performed: Removed existing water heater from premises and properly disconnected all electrical and plumbing connections. Drained and disposed of old water heater in accordance with standard removal procedures. Supplied and installed (1) new A.O. Smith residential electric water heater. Included 6-year manufacturer warranty on new water heater unit. Installed new hot and cold water shut off valves for improved serviceability and future maintenance. Installed new temperature and pressure relief valve. Installed new discharge piping for relief valve to meet proper safety standards. Reconnected hot and cold water supply lines using all necessary piping fittings and approved materials. Installed new dielectric connections where required to help reduce corrosion and extend system life. Reconnected electrical wiring and verified proper voltage to unit. Secured water heater in place and confirmed proper positioning. Filled tank

Bathroom Plumbing Repair: Dispatched to a home where the shower was experiencing fluctuating water temperature. Diagnosed a failing mixing valve inside the shower wall. Replaced the valve, recalibrated temperature settings, and tested water flow. Shower now maintains consistent temperature and pressure.

Work Performed: Supplied and professionally installed (1) new A.O. Smith 50-gallon electric water heater Removed existing water heater and disposed of properly Installed new thermal expansion tank for system protection Installed new shutoff valve for improved serviceability Connected unit to existing hot and cold water lines with proper fittings Installed drain pan and ensured proper clearance in closet space Secured electrical connections and verified proper voltage supply Filled tank and properly purged air from system Tested for proper operation and ensured no leaks present Verified hot water delivery and thermostat functionality Cleaned up work area upon completion

Work Performed: Removed existing worn tub/shower trim components Supplied and installed new single-handle shower valve trim kit Installed new chrome tub spout with proper alignment and secure connection Inspected valve operation and ensured smooth handle function Checked for proper water temperature control and balanced flow Tested all connections for leaks and verified watertight seal at wall penetrations Applied clean finish and ensured all trim sits flush against tile surface Cleaned up work area upon completion and removed all debris

Water Heater Maintenance: Arrived for a scheduled maintenance on a hybrid water heater. Inspected internal components, flushed the tank, tested pressure relief valves, and verified optimal temperature control. Confirmed reliable, energy-efficient hot water operation.

Sewer Repair: Homeowner reported repeated backups in the main sewer line. Performed a camera inspection revealing significant root intrusion and pipe deterioration. Excavated the affected section, replaced the sewer line with durable piping, and tested flow to restore reliable wastewater drainage.

Water Heater Repair Service: Arrived to address a water heater that was not heating efficiently. Drained and flushed the tank to remove sediment buildup, replaced the heating element, and tested temperature output at multiple faucets. Confirmed restored hot water performance.

Water Filtration System Installation: Homeowner requested a water filtration system installation. Installed an under-sink filtration unit, connected it to the cold water supply, secured all fittings, and tested water flow and filter operation. Verified improved water quality at all designated outlets.

Drain Repairs: Responded to a call from a homeowner reporting a slow-draining kitchen sink. Inspected the P-trap and interior drain line, finding a buildup of grease and food debris. Used a professional-grade auger to remove the obstruction and hydro-jetted the drain to flush remaining buildup. Verified smooth flow and proper drainage throughout the sink.

Work Performed: Diagnosed running toilet and improper tank refill Removed and replaced toilet fill valve assembly Adjusted float and water level for proper operation Tested multiple flush cycles to ensure no leaks present Cleaned up work area upon completion

Work Performed: • Supplied and installed two new toilet fill valves. • Supplied and installed two new two-inch toilet flappers. • Adjusted water levels and calibrated fill valves for proper operation. • Tested each toilet for leaks and verified correct flushing performance. • Cleaned up work area upon completion.

Work Performed: Removed existing damaged exterior shutoff valve Installed new brass gate valve with red handle Properly threaded and sealed connection to existing water line Secured and aligned valve flush to exterior wall Tested valve operation for proper shutoff and flow Ensured no leaks present after installation Cleaned up work area upon completion

Installed a new Moen pull down kitchen faucet with a high arc spring design. Secure mounting and proper water connections completed. Tested for smooth operation proper spray function and no leaks.

Shower drain clog removed after clearing a heavy buildup of hair and debris that was restricting flow. Drain was mechanically cleaned and tested to ensure proper drainage and normal operation was restored.

Drain Repair Service: The client reported slow drainage in multiple bathrooms and the kitchen sink. Inspection revealed soap residue, grease, and scale lining the drain pipes. I used high-pressure hydro-jetting equipment to clean the interior pipe walls completely, restoring proper flow and preventing future blockages.

Outdoor Plumbing Repair: The homeowner noticed low water pressure at the exterior hose bib and muddy ground near the foundation. I located a cracked underground supply line caused by shifting soil. The area was excavated, the damaged section of pipe replaced with new PVC piping, and the system was pressure-tested to ensure proper operation.

Bathroom Plumbing Repair: The customer complained of constant running from the toilet and weak flushing performance. Inspection revealed a deteriorated flapper and a misaligned fill valve. I replaced both components, adjusted the water level, checked for internal leaks, and verified proper flushing operation before leaving the property.

Work Performed: • Removed existing bathroom commode and prepared flange and mounting surface • Installed customer supplied Toto bathroom commode • Installed new wax ring and secured toilet to flange • Reconnected water supply and adjusted fill and flush operation • Tested for proper operation and ensured no leaks present • Cleaned up work area upon completion

Water Heater Repair: A client experienced inconsistent water temperatures due to a failing heating element and sediment buildup. I drained the tank, replaced the defective element, tested the thermostat, and verified water output at multiple fixtures, restoring consistent hot water supply and improving efficiency.