Coconut Creek, FL

Work Performed: • Removed existing kitchen faucet and drain components. • Prepared sink deck and mounting surface for new fixture installation. • Supplied labor to install customer-supplied matte black pull-down kitchen faucet. • Installed new faucet assembly and secured mounting hardware. • Connected hot and cold water supply lines to existing angle stops. • Installed and connected faucet sprayer hose and counterweight assembly. • Removed existing sink strainer assembly. • Installed new basket strainer and sealed drain opening for leak-free operation. • Tightened and secured all water and drain connections. • Restored water service and tested faucet operation. • Verified proper hot and cold water flow, pressure, and temperature control. • Tested pull-down sprayer function and faucet retraction system. • Performed leak test on all supply line and drain connections. • Confirmed proper operation of kitchen sink and faucet assembly at time of service. • Cleaned work area

Work Performed: • Responded to the property after the homeowner reported water leaking through the ceiling. • Performed an investigation of the affected area to determine the source of the water intrusion. • Removed and opened a section of the ceiling drywall to gain access for inspection and leak detection purposes. • Conducted a visual inspection of the exposed plumbing and surrounding areas above the ceiling. • Traced the source of the leak to the shower area and performed further evaluation of the shower assembly. • Determined that the leak is originating from the existing shower pan and not from the exposed water supply or drain piping. • Verified signs of water intrusion consistent with a failed or compromised shower pan system. • Advised the homeowner of findings and recommended repair or replacement of the shower pan and any associated waterproofing components as needed. • Area was left accessible for further repairs and evaluation by the appropriate

### Work Performed: • Installed new garbage disposal unit under kitchen sink. • Removed existing disposal unit as needed to complete new installation. • Prepared sink flange and mounting assembly for proper disposal connection. • Installed and secured disposal mounting bracket to kitchen sink drain opening. • Mounted new garbage disposal unit securely in place. • Connected disposal discharge outlet to existing kitchen drain piping. • Reworked under-sink drain connection as needed for proper alignment. • Installed and adjusted drain piping to ensure proper pitch and drainage. • Connected dishwasher drain line to garbage disposal inlet connection. • Verified dishwasher drain connection was properly secured. • Connected disposal electrical cord and confirmed power connection was secure. • Tested garbage disposal for proper operation. • Ran water through sink and disposal to confirm proper drainage. • Checked disposal mounting assembly for proper seal. • Inspected all visi

Work Performed: • Supplied and installed new whole house water treatment system. • Supplied and installed new mineral tank with digital control valve for automatic system operation. • Supplied and installed new brine tank for the water conditioning system. • Positioned and leveled new water treatment equipment in designated garage area. • Connected incoming main water supply line to new treatment system. • Connected outgoing treated water line back into the home plumbing system. • Installed new piping connections and fittings necessary for proper system installation. • Connected brine line from control valve to brine tank. • Programmed digital control valve for proper service cycle and regeneration cycle. • Pressurized system and checked all visible connections for leaks. • Flushed system after installation and confirmed proper water flow. • Confirmed no active leaks were present at the time of completion. • Cleaned up work area upon completion and left system ready for

Work Performed: • Removed existing bathroom plumbing fixtures and prepared area for new fixture installation • Installed new bathtub and shower enclosure assembly with all necessary drain and plumbing connections • Installed new shower valve trim and verified proper hot and cold water operation • Installed new toilet and connected to existing drainage and water supply system • Installed new bathroom vanity with sink and completed all necessary faucet and drain connections • Secured and aligned all fixtures properly to ensure stable and professional installation • Tested bathtub shower sink and toilet for proper drainage water flow and leak free performance • Performed final operational testing and ensured all plumbing fixtures were functioning correctly • Cleaned work area and removed installation related debris upon completion.

Work Performed: Supplied and installed new commercial floor-mounted toilet in restroom. Removed existing toilet and prepared flange area for installation of new fixture. Set new commercial toilet in place with proper seal and secured unit for stable operation. Reconnected flushometer / flush valve assembly to new toilet and verified proper alignment. Connected water supply components as needed for proper restroom operation. Tested toilet and flush valve assembly for proper flushing performance and refill operation. Inspected base of toilet, flush connection, and visible supply connections to ensure no leaks were present. Confirmed fixture was operating properly and draining as intended at time of completion. Cleaned up work area upon completion.

Work Performed: Arrived on site and inspected custom shower system due to reported drainage and fixture concerns. Protected surrounding bathroom finishes and prepared work area for service. Removed existing shower drain cover and accessed drain assembly. Performed professional drain cleaning service to clear blockage and restore proper drainage. Flushed drain line and tested multiple times to verify water was draining properly. Inspected shower valve trim shower head and handheld components for proper operation. Tightened loose fixture connections and adjusted mounting hardware where needed. Checked hot and cold water balance and verified correct temperature control. Inspected shower pan walls and visible plumbing penetrations for signs of leaks. Confirmed proper flow from shower head and handheld spray assembly. Reinstalled drain cover and ensured all components were secure. Cleaned work area upon completion.

Work Performed: Supplied and professionally installed (1) new toilet Removed existing toilet and disposed of properly Installed new reinforced wax seal and closet bolts Set and secured toilet to flange ensuring proper alignment Connected water supply line and adjusted fill valve as needed Sealed base of toilet for a clean finished look Tested for proper operation and ensured no leaks present Cleaned up work area upon completion

Work Performed: Removed existing toilet and prepared flange area for new installation Installed new DeerValley toilet including new wax ring and closet bolts Secured toilet to flange and ensured proper alignment and stability Connected water supply line and adjusted fill valve components Tested multiple flush cycles to confirm proper operation and seal Checked for leaks at base and supply connection Cleaned up work area upon completion.

Supplied two Delta Classic bathroom faucet sets for upcoming installation. Fixtures staged on site and verified for completeness prior to install. Ready for same day replacement and upgrade.